China Hot selling China Supplier Small Speed Reducer Gearbox Exported to CZPT gearbox assembly

Product Description

Product Description

DESCRIPTION:
Gear reducers are enclosed helical gears with hollow inputs.
The gear is mounted directly on the input shaft of the gear and receives support from a motor mounting bracket mounted on the machine housing. 
No additional parts are required to transfer torque from the reducer to the machine.
It can be mounted in vertical, horizontal or inclined position.
Shaft-mounted gear reducers typically have 5:1 7:1 10:1 reduction ratios and output speeds ranging from 1 to 300 rpm.

M4 series gear reducer can be installed directly on screw conveyors and feeders with a XUH seal installed on the output shaft of the gearbox. 
Ensure that cement, and fly ash powder will not get into the gearbox and extend the service life of the gearbox.
More suitable for bulk materials, grain and aggregate handling industries

 

WORKING PRINCIPLE:
M4 series gearboxes come in 5 sizes (M41 / M43 / M45 / M47 / M49). 
Nominal gear ratios are in accordance with Ra 10 CHINAMFG 2017 (5, 6, 7, 10). Cylindrical gears with helicoidal teeth. 
M4 series gearboxes can be mounted directly on screws: in this case, the XUH type output shaft seal is usually installed. 
M4 series gearboxes are supplied with grease for use at ambient temperatures (0°C – 40°C).

PROPERTIES:
– Helical gearbox
– Nominal torque that can be transferred to the output shaft: up to 1500 Nm.
– Installed power at the input up to 30 kW.
– Operation at ambient temperature (0°C – 40°C).
– DIN 5482 involute spline output shafts
– Flange mounting on motor and output side
– Precision-machined cylindrical bevel gears with teeth.
– Flange mounting on motor and output side

BENEFITS:
– Easy installation
– Quick maintenance
– Low installation costs

 

 

 

Services

 

Pre-sales Commitment

1. For user inquiries, quick response, warm reception, and answer all questions.
2. Provide detailed design information free of charge within 24 hours.

Commitment in Sales

1. All ex-factory products meet the quality standards specified in the contract. All products are tested according to customer requirements before delivery.
2. After the contract is signed, the customers are welcome to the site of our company for supervision.

After-sales Commitment

1. We provide technical support for customers. If necessary, the product can be debugged on-site, and relevant operators can be trained to solve user problems.
2.  24 hours to solve the problems for customers. Product use a day, a day of service.
3. Set up a high-quality service team, and set up product files for regular return visits.

/* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Application: Machinery
Hardness: Hardened Tooth Surface
Installation: Vertical Type
Layout: Coaxial
Gear Shape: Conical – Cylindrical Gear
Step: Four-Step
Samples:
US$ 100/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

Customized Request

speed reducer gearbox

Ensuring Precision of Gear Tooth Profiles in Speed Reducer Gearboxes

Manufacturers employ several techniques to ensure the precision of gear tooth profiles in speed reducer gearboxes, which is crucial for optimal performance and longevity:

  • High-Quality Materials: Manufacturers use high-quality materials for gear manufacturing, such as hardened steel or specialized alloys, to enhance durability and minimize wear.
  • Precision Machining: Advanced machining processes, including CNC (Computer Numerical Control) machining and grinding, ensure accurate tooth profiles and precise gear dimensions.
  • Tooth Profile Design: Detailed tooth profile designs based on mathematical calculations and engineering principles help optimize meshing and minimize stress concentration.
  • Tooth Forming Techniques: Various tooth forming methods, such as hobbing, shaping, and broaching, are employed to create accurate gear tooth profiles with minimal deviations.
  • Heat Treatment: Heat treatment processes like carburizing, quenching, and tempering are used to achieve the desired hardness and strength, ensuring gear teeth can withstand operational stresses.
  • Quality Control: Rigorous quality control measures, including inspection using precision tools like coordinate measuring machines (CMMs), ensure compliance with design specifications.
  • Lubrication and Surface Coatings: Proper lubrication and specialized surface coatings help reduce friction and wear, maintaining accurate tooth profiles during operation.

By implementing these techniques and adhering to stringent quality standards, manufacturers can achieve the required precision in gear tooth profiles, resulting in smooth and efficient operation of speed reducer gearboxes.

speed reducer gearbox

Maintenance Practices for Extending the Lifespan of Speed Reducer Gearboxes

Proper maintenance is essential for ensuring the longevity and optimal performance of speed reducer gearboxes. Here are some crucial maintenance practices to extend their lifespan:

Regular Inspection: Conduct routine visual and auditory inspections to identify any signs of wear, misalignment, or unusual noise. Detecting issues early allows for timely intervention and prevents further damage.

Lubrication: Follow the manufacturer’s guidelines for lubrication frequency and type. Adequate lubrication ensures smooth gear operation, reduces friction, and prevents premature wear and overheating.

Lubricant Quality: Use high-quality lubricants recommended by the gearbox manufacturer. Proper lubricant selection contributes to effective lubrication and protection against corrosion.

Cleaning: Regularly clean the exterior of the gearbox to prevent the accumulation of dirt, debris, and contaminants that could impact its performance and cooling ability.

Torque Check: Periodically check and re-tighten mounting bolts and fasteners to maintain proper torque and prevent loosening due to vibrations and operational forces.

Alignment: Ensure proper shaft alignment to minimize excessive loads on gears and bearings. Misalignment can lead to increased wear and reduced efficiency.

Temperature Monitoring: Monitor the operating temperature of the gearbox and ensure it stays within the recommended range. Excessive heat can degrade lubricant properties and damage internal components.

Seal Inspection: Check seals and gaskets for signs of leaks. Damaged seals can lead to lubricant loss and contamination, affecting gearbox performance.

Filter Replacement: If the gearbox has a filtration system, regularly replace filters to maintain clean lubricant and prevent abrasive particles from causing damage.

Vibration Analysis: Perform periodic vibration analysis to detect any abnormal vibrations that could indicate misalignment, imbalance, or other issues. Addressing these problems promptly can prevent further damage.

Professional Service: Engage with qualified technicians or service providers for comprehensive inspections and maintenance, especially for complex or critical applications.

By adhering to these maintenance practices, you can maximize the lifespan of your speed reducer gearboxes, ensure reliable operation, and avoid costly downtime or premature replacement.

speed reducer gearbox

What Advantages Does a Speed Reducer Gearbox Offer in Industrial Applications?

A speed reducer gearbox provides numerous advantages that make it a valuable component in a wide range of industrial applications. These advantages contribute to improved efficiency, performance, and reliability of machinery and equipment.

1. Speed Reduction: One of the primary benefits of a speed reducer gearbox is its ability to reduce the rotational speed of an input shaft, which is often provided by a high-speed power source such as an electric motor. This speed reduction is crucial in applications where the output speed needs to be lower than the input speed to achieve optimal performance. For example, in manufacturing processes or conveyor systems, a slower output speed is often necessary for precise control and safe handling of materials.

2. Torque Increase: The gear arrangement within a speed reducer gearbox leads to an increase in torque at the output shaft compared to the input shaft. This torque amplification is essential for applications that require higher levels of force to overcome resistance, move heavy loads, or perform work. The gearbox’s ability to multiply torque ensures that machinery can handle demanding tasks effectively.

3. Mechanical Advantage: Speed reducer gearboxes utilize gear trains and ratios to create a mechanical advantage. This advantage allows the gearbox to convert high-speed, low-torque input power into low-speed, high-torque output power. The mechanical advantage enhances the efficiency of power transmission and motion control, making it well-suited for applications that involve both speed reduction and torque increase.

4. Versatility: Speed reducer gearboxes are highly versatile and can be tailored to specific application requirements. Manufacturers offer a variety of gear ratios, sizes, and configurations, allowing for customization to achieve the desired output characteristics. This adaptability ensures that gearboxes can be integrated into a wide range of machinery and equipment across different industries.

5. Smooth Operation: The precise meshing of gears in a speed reducer gearbox results in smooth and consistent power transmission. This characteristic is crucial for applications that demand accurate and controlled movement, such as robotics and automated systems. The gearbox’s ability to maintain steady motion contributes to the overall efficiency and performance of the system.

6. Energy Efficiency: By converting high-speed, low-torque input power into a lower-speed, higher-torque output, speed reducer gearboxes help optimize energy usage. This energy-efficient operation can lead to reduced power consumption, lower operating costs, and improved sustainability in industrial processes.

7. Noise and Vibration Reduction: The gear arrangement in a speed reducer gearbox can help dampen noise and vibrations produced by the power source. This is particularly beneficial in applications where noise reduction is essential for a comfortable working environment or to prevent damage to sensitive equipment.

In summary, a speed reducer gearbox offers advantages such as speed reduction, torque amplification, mechanical advantage, versatility, smooth operation, energy efficiency, and noise reduction. These benefits make speed reducer gearboxes indispensable components in various industrial settings, enhancing the overall performance and productivity of machinery and systems.

China Hot selling China Supplier Small Speed Reducer Gearbox Exported to CZPT   gearbox assembly	China Hot selling China Supplier Small Speed Reducer Gearbox Exported to CZPT   gearbox assembly
editor by CX 2024-02-08